Starting again from scratch (almost!)

Here you can see the most obvious of the holes, in the diesel tank, that were behind the weedhatch, there were several smaller holes too.

The diesel tank drain was an upside down length of channel with a tap welded into the end, I decided to cut this out too, as we now have the inspection hatch, we can easily clean out the tank, and there is now a centrifugal filter to catch anything else.

The three old tank panels have been completely removed new panels welded into place ;o) One of the old panels is lying on the 'moon pool'

The new weedhatch sides welded in.

The first three flanges were welded on before it got a bit late to be working, the fourth will be added tomorrow.

One step forwards and two steps back

Back to the drawing board! I decided that we would need to take radical action, chopping out the rear deck drain channels, then the entire weedhatch!

We found that the diesel tank had rusted through, behind the weedhatch, so a large section of the tank got the chop.

I could now get at the narrow area around each side of the tank. I, once again, cleaned out the tank, finally getting at the last deposits in these, hard to get to, areas.

The water is scarily close to the opening! LOL! The things you do to save paying for drydock or slipway!

Fix a problem and find more problems

When I cut the deck drain off the counter plate this was all that was left of the steel.

This is what the 'good' one looked like!!!!

We welded a plug in each hole and then over-plated, we'll re-route the deck drain through a skin fitting later

We added a lot of steel and welds and still the diesel bled through pinholes in the weld and started to weep into the weedhatch in tiny quantities, but it would only get worse.

So we have to bite the bullet and get her up on our marina's new slipway, I will cut out the weedhatch and we'll replace it with a new one, I also cut out some of the newly added steel so that we can eliminate the void/rust-trap between the weedhatch and the diesel tank and then overplate diesel tank.

If the pre-purchase surveyor had done his job properly, he would have found these problems, but all he said was there was some rust around the weedhatch that could be treated! Had he picked up on the dangerous faults, we could have done all this while we were in dry-dock last August. Grrr!

A labour of love ;o)

More than twenty years ago I was at a bubblecar rally in my Messerschmitt kr200, at the time I had no serious longings to own a narrowboat.

We went for a wander on the Hatton flight and visited the craft centre where I bought four small pieces of different hardwoods that I could carve into traditional Welsh lovespoons.

These bits of wood have been moved from pillar to post over the years and I have never got around to making anything from them. Recently I found them when we were moving out of my garage in Cardiff.

I decided it was time to make my lovely lady a lovespoon that would reflect my love for her and our love for our pair of boats and in doing so, re-unite the piece of rosewood with it's canal based origins.

Pencil drawing the design on the piece of rosewood

I rigged the fretsaw attachment to my treadle lathe

USB LEDs, bought from a pound shop, help me see what I'm cutting

It was about this time that my chisel slipped and chopped the top off my little finger! I struggled to find the piece in the woodchips and to open the first aid kit with one hand. Once I found the lost bit of finger, complete with fingernail, I went around my neighbour's boats asking for superglue to stick it back on, Rita insisted that she clean my wound and patch me up minus the bit! "Too many germs", she said.

So now the lovespoon was rosewood with a splash or two of my blood! Love or what? LOL!

Freyja takes shape

Freyja and Christina roughed out

Starting to take shape

Busy working on the real boats at the moment, hopefully get a chance to carve the finer details when I'm back out on tour.

Another quick job that wasn't so quick........

After I painted our engine I wanted to get the rest of the engine 'ole cleaned, de-rusted and painted. While stripping the flakey bits of rust off I found a few things that needed attention, first, I noticed that a little water was seeping out from around the deck-drain (where it was welded to the swim)

A combination of the water trapped in the rust flakes, blocked deck-drains and bad design caused this annoying seepage, we're chopping them both off, plating them over and making new deck drains that will exit through skin fittings ;o)

Secondly, I found that the brackets that hold the weed-hatch lid down had almost rusted away, this should have been picked up on the pre-purchase survey, Grrrr!

Very glad I decided to go the whole hog and clean everything back to clean metal or I wouldn't have found these problems before they became a bigger problem.

The third problem was a diesel seepage from behind the weedhatch, but I couldn't see exactly where it was coming from.

Tiny pinholes hidden behind the remnants of the weedhatch flange. once again a moisture trap had been created causing this to rust through.

After cutting off the top edge of the weedhatch a length of angle-iron was welded on.

Mark from Nene Marine busy with the welder.

A nice new shiny weedhatch flange, the bottom edge of the fuel tank has been re-enforced and the deck-drain has been chopped back and will be removed and plated.

After chopping off the weedhatch brackets we cut the rusty bit off and welded new bottoms onto them

Once the welds are ground back and the metal treated with rust-converter, I'll prime it all and then give a good few coats of light grey garage floor paint.

Nature comes to us

Today, as I walked along the pontoon, I spotted this heron, obviously spellbound by our Welsh flag, or maybe he was taking a fancy to Glenda's herbs on Christina's stern.

This pretty little pansy found a place to grow on Christina's roof.     (I must get around to changing the 'S. & G. Trading' to 'C. & G. Trading', as I have on the the other side of both boats)

How green was my engine.

Or...............

How I got a B.R.G.  B.M.C. by A.M.C.!

To the shock, horror and consternation of some of our neighbours, I'm 'pimping our bilge'!

I've de-cluttered, de-greased and have started de-rusting our bilge, in preparation for painting it with light grey garage floor paint, I've also de-greased the B.M.C. engine (marinised by A.M.C.) so I decided to give it a lick of paint B.R.G. (British Racing Green)

The newly painted engine with it's nice new exhaust pipe ;o)

Now I need to finish de-rusting in the bilge, I'll treat it with Fertan rust converter and then paint it light grey.

The bit that has the traditionalists up in arms is the fact that I'm going to fit what's left of my self-adhesive LED strip under the deck so that I can see what I'm doing when I'm in the engine 'ole.